VCA | PartQuest™ Explore

Copy of Motion Control with Voice Coil Actuator (VCA) - CPF Plant - on Wed, 07/01/2020 - 16:26

francisco.eduardo.ortiz
Designer231374

francisco.eduardo.ortiz

Member for

4 years 7 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a VCA driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalent

The top net in this schematic represents the displacement of an ideal position sensor, which provides the actual target position feedback. The loop compensation was designed by using "AC" or frequency-domain analysis of the open loop transfer function. The results are shown in the Magnitude and Phase difference plots (sensor_displacement - feedback). The loop crossover is seen to be at approximately 100 Hz, and the phase margin is just over 44 degrees. The corresponding time-domain step response is shown in the left-most waveform plot.

You can see this same design and analysis using the original mechanical structural model for the "plant" here:

https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-physical-plant

You can see a more detailed model of this system, that includes the Power Electronics section (i.e. a PWM controlled MOSFET H-Bridge used to drive the VCA), here: https://www.systemvision.com/design/motion-control-vca-pwm-drive

About text formats

Copy of Motion Control with Voice Coil Actuator (VCA) - CPF Plant - on Wed, 07/01/2020 - 16:26

francisco.eduardo.ortiz
Designer231374

francisco.eduardo.ortiz

Member for

4 years 7 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a VCA driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalent

The top net in this schematic represents the displacement of an ideal position sensor, which provides the actual target position feedback. The loop compensation was designed by using "AC" or frequency-domain analysis of the open loop transfer function. The results are shown in the Magnitude and Phase difference plots (sensor_displacement - feedback). The loop crossover is seen to be at approximately 100 Hz, and the phase margin is just over 44 degrees. The corresponding time-domain step response is shown in the left-most waveform plot.

You can see this same design and analysis using the original mechanical structural model for the "plant" here:

https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-physical-plant

You can see a more detailed model of this system, that includes the Power Electronics section (i.e. a PWM controlled MOSFET H-Bridge used to drive the VCA), here: https://www.systemvision.com/design/motion-control-vca-pwm-drive

About text formats

Copy of Motion Control with Voice Coil Actuator (VCA) - CPF Plant - on Sun, 04/19/2020 - 23:20

prof.rodolfo.epge
Designer230576

prof.rodolfo.epge

Member for

4 years 8 months

109

designs

10

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a VCA driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalent

The top net in this schematic represents the displacement of an ideal position sensor, which provides the actual target position feedback. The loop compensation was designed by using "AC" or frequency-domain analysis of the open loop transfer function. The results are shown in the Magnitude and Phase difference plots (sensor_displacement - feedback). The loop crossover is seen to be at approximately 100 Hz, and the phase margin is just over 44 degrees. The corresponding time-domain step response is shown in the left-most waveform plot.

You can see this same design and analysis using the original mechanical structural model for the "plant" here:

https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-physical-plant

You can see a more detailed model of this system, that includes the Power Electronics section (i.e. a PWM controlled MOSFET H-Bridge used to drive the VCA), here: https://www.systemvision.com/design/motion-control-vca-pwm-drive

About text formats

Copy of Motion Control with Voice Coil Actuator (VCA) - CPF Plant - on Sat, 02/01/2020 - 18:34

ayari.riadh
Designer229374

ayari.riadh

Member for

4 years 10 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a VCA driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalentThe top net in this schematic represents the displacement of an ideal position sensor, which provides the actual target position feedback. The loop compensation was designed by using "AC" or frequency-domain analysis of the open loop transfer function. The results are shown in the Magnitude and Phase difference plots (sensor_displacement - feedback). The loop crossover is seen to be at approximately 100 Hz, and the phase margin is just over 44 degrees. The corresponding time-domain step response is shown in the left-most waveform plot.You can see this same design and analysis using the original mechanical structural model for the "plant" here:https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-physical-plantYou can see a more detailed model of this system, that includes the Power Electronics section (i.e. a PWM controlled MOSFET H-Bridge used to drive the VCA), here: https://www.systemvision.com/design/motion-control-vca-pwm-drive

About text formats

TDFS for VCA - PWM Drive

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,700

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

xxxx This example shows a voice coil actuator (VCA) driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalentThis version of the control system is useful when you are designing the physical implementation of the electronics (i.e. choosing properly sized Power MOSFETs, selecting an appropriate PWM switching frequency, etc.). You can use that complex-pole fitted model to assess the electronics-mechanical dynamic interactions and overall system behavior. This level of design implementation detail is typically used after the control compensation has been designed using continuous (non-switching) linearizable component models, as in this version of the system model: https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-cpf-plant

About text formats

Spring-Mass Structural Model and Fitted Equivalent

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,700

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

About text formats

Motion Control with Voice Coil Actuator (VCA) - Physical Plant

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,700

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

About text formats

Motion Control with VCA - PWM Drive

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,700

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example shows a voice coil actuator (VCA) driven motion control loop that is acting through an equivalent model of a flexible mechanical structure. This model is shown on the right side of the schematic. It was calibrated to match a physical structure, based purely on its frequency response data and using the HyperLynx complex-pole fitting technology. The original mechanical model can be seen here: https://www.systemvision.com/design/spring-mass-structural-model-and-fitted-equivalentThis version of the control system is useful when you are designing the physical implementation of the electronics (i.e. choosing properly sized Power MOSFETs, selecting an appropriate PWM switching frequency, etc.). You can use that complex-pole fitted model to assess the electronic-mechanical dynamic interactions and overall system behavior.This level of design implementation detail is typically used after the control compensation has been designed using continuous (non-switching) linearizable component models, as in this version of the system model: https://www.systemvision.com/design/motion-control-voice-coil-actuator-vca-cpf-plant

About text formats

Terms of Use Cookie Notice Data Privacy Notice

francisco.eduardo.ortizDesigner231374

Member for

francisco.eduardo.ortizDesigner231374

Member for

prof.rodolfo.epgeDesigner230576

Member for

ayari.riadhDesigner229374

Member for

Mike DonnellyDesigner19

Member for

Mike DonnellyDesigner19

Member for

Mike DonnellyDesigner19

Member for

Mike DonnellyDesigner19

Member for

francisco.eduardo.ortiz
Designer231374

francisco.eduardo.ortiz
Designer231374

prof.rodolfo.epge
Designer230576

ayari.riadh
Designer229374

Mike Donnelly
Designer19

Mike Donnelly
Designer19

Mike Donnelly
Designer19

Mike Donnelly
Designer19