PartQuest Explore Promote

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Thu, 03/04/2021 - 15:24

Designer238518

Member for

4 years

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sun, 02/21/2021 - 22:39

Designer238385

Member for

4 years 1 month

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sun, 02/21/2021 - 22:39

Designer238385

Member for

4 years 1 month

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sun, 12/13/2020 - 22:32

Designer236981

Member for

4 years 3 months

33

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sat, 12/05/2020 - 22:08

Designer237029

Member for

4 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sat, 12/05/2020 - 22:04

Designer237029

Member for

4 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

Copy of Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sat, 12/05/2020 - 22:04

Designer237029

Member for

4 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

TEC Sim VL

Designer236539

Member for

4 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.

The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

Copy of Laser Temperature Regulator using Peltier TEC - on Sun, 11/15/2020 - 11:25

Designer236539

Member for

4 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.

The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.