Switching Converter | PartQuest™ Explore

Transient Stability Testing of Transmission Line Fed LED Driver

Designer19

Member for

12 years 2 months

1,973

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

About text formats

TDFS Impedance Stability of Transmission Line Fed LED Driver - Switching

Designer19

Member for

12 years 2 months

1,973

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the use of the TDFS method (Time Domain Frequency Sweep) to measure impedance stability ratio. The system is a switching DC/DC step-down power converter used for LED lighting, supplied by a battery through a long power cable.The TDFS impedance stability measurement model applies a 0.2A sinusoidal stimulus current at the point where the cable connects to the converter. The voltage at that point, as well as the stimulus current splits (toward the source and the load) are measured, and the associated source and load impedances vs. frequency are computed.The ratio of the source to load impedance is the impedance stability ratio (Tm). Similar to the open-loop frequency response requirement for closed-loop stability, Tm must not have magnitude = 1.0 at phase = 180 degrees, at any frequency.For this system, with a cable length of 400 meters and 8 AWG wire, the results show that the impedance ratio magnitude (green waveform) reaches unity (0 dB) at close to 2 kHz, where the phase (light blue waveform) is approximately 165 degress. This implies a "phase margin" of only 15 degrees, For a longer cable, this margin is further reduced. As shown in the companion example, "Transmission Line Fed LED Driver - Switching", for the cable length = 800 meters the system is unstable.This instability is the result of the "source" impedance (which includes the cable) variation over frequency, interacting with the varying load impedance. Note that at low frequency, the load effectively has a negative impedance, due to the constant power nature of the DC to DC converter.

About text formats

Step-Down (Buck) DC to DC Converter - Switching

Designer19

Member for

12 years 2 months

1,973

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example&nbsp;"Step-Down (Buck) DC to DC Converter - Continuous” you can find here:

https://explore.partquest.com/node/128081

This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Copy of TDFS Loop Stability for Step-Down DC to DC (Buck) Converter - Switching - on Thu, 01/22/2026 - 15:10

Designer230346

Member for

5 years 10 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Copy of Transient Stability Testing of Transmission Line Fed LED Driver - on Thu, 01/22/2026 - 14:29

Designer264735

Member for

6 days 2 hours

1

designs

1

groups

Welcome to the community!!

Description

About text formats

Copy of Transient Stability Testing of Transmission Line Fed LED Driver - on Fri, 11/28/2025 - 14:51

Designer249130

Member for

2 years 4 months

34

designs

1

groups

Welcome to the community!!

Description

About text formats

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Wed, 10/29/2025 - 11:13

Designer264029

Member for

2 months 4 weeks

1

designs

1

groups

Welcome to the community!!

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example&nbsp;"Step-Down (Buck) DC to DC Converter - Continuous” you can find here:https://explore.partquest.com/node/128081This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Tue, 10/21/2025 - 22:56

Designer262802

Member for

7 months 3 weeks

3

designs

1

groups

Welcome to the community!!

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example&nbsp;"Step-Down (Buck) DC to DC Converter - Continuous” you can find here:https://explore.partquest.com/node/128081This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Thu, 10/16/2025 - 22:32

Designer255461

Member for

1 year 9 months

2

designs

1

groups

Welcome to the community!!

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example&nbsp;"Step-Down (Buck) DC to DC Converter - Continuous” you can find here:https://explore.partquest.com/node/128081This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Sat, 09/20/2025 - 15:37

Designer259698

Member for

1 year 2 months

11

designs

1

groups

Welcome to the community!!

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example&nbsp;"Step-Down (Buck) DC to DC Converter - Continuous” you can find here:

https://explore.partquest.com/node/128081

This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Troubleshooting Terms of Use Cookie Notice Data Privacy Notice