PID | PartQuest™ Explore

Laser Temperature Regulator using Peltier TEC

Designer19

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.

https://www.systemvision.com/design/laser-temperature-regulator-tdfs

But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

About text formats

Laser Temperature Regulator using Peltier TEC - on Mon, 12/23/2024 - 17:09

Designer260333

Description

https://www.systemvision.com/design/laser-temperature-regulator-tdfs

About text formats

Copy of Laser Temperature Regulator using Peltier TEC - on Sat, 09/09/2023 - 20:53

Designer249287

Description

The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

About text formats

TEC Sim VL

Designer236539

Description

About text formats

Copy of Laser Temperature Regulator using Peltier TEC - on Sun, 11/15/2020 - 11:25

Designer236539

Description

About text formats

Copy of Laser Temperature Regulator using Peltier TEC - on Fri, 09/18/2020 - 10:42

Designer219536

Description

About text formats

Copy of tuning ziegler pid haro - on Wed, 08/12/2020 - 22:25

Designer233532

Description

About text formats

Laser Temperature Regulator using Peltier TEC and Vishay Thermistor

Designer19

Description

This "Live Application" example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A Vishay thermistor from our Partner Library, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation.All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance of the "laser", which is just a simple resistance heating element for this example, to change the power dissipation level. You can also change the heat transfer resistance values in the thermal network, to see their effect on system performance. Finally, you can change the PID control block gains and see the effect on the steady-state and transient behavior of this temperature regulation system.Note: You can move the waveform probes to see any other signal in the system.

About text formats

Laser Temperature Regulator using Peltier TEC with Vishay TFPT temperature sensor

Designer208121

Description

About text formats

Laser Temperature Regulator using Peltier TEC with Vishay PTS temperature sensor

Designer208121

Description

About text formats

Laser Temperature Regulator using Peltier TEC

Designer19

Laser Temperature Regulator using Peltier TEC - on Mon, 12/23/2024 - 17:09

Designer260333

Copy of Laser Temperature Regulator using Peltier TEC - on Sat, 09/09/2023 - 20:53

Designer249287

TEC Sim VL

Designer236539

Copy of Laser Temperature Regulator using Peltier TEC - on Sun, 11/15/2020 - 11:25

Designer236539

Copy of Laser Temperature Regulator using Peltier TEC - on Fri, 09/18/2020 - 10:42

Designer219536

Copy of tuning ziegler pid haro - on Wed, 08/12/2020 - 22:25

Designer233532

Laser Temperature Regulator using Peltier TEC and Vishay Thermistor

Designer19

Laser Temperature Regulator using Peltier TEC with Vishay TFPT temperature sensor

Designer208121

Laser Temperature Regulator using Peltier TEC with Vishay PTS temperature sensor

Designer208121

Member for

Member for

Member for

Member for

Member for

Member for

Member for

Member for

Member for

Member for