PartQuest Explore Promote

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

cooler

Kares
Designer98036

Kares

Member for

7 years 10 months

4

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

Peltier Hook up

akerr
Designer80086

akerr

Member for

8 years 1 month

3

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Regulator temperatury lasera using Peltier TEC

AntoniLeniewski
Designer130096

AntoniLeniewski

Member for

7 years 5 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

Laser Diode Temperature Regulator using Peltier TEC

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

NOT Finished, "laser diode" may not be a practical size yet ...This example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A thermistor, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature, and 180 degrees out of phase.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation. These gains were selected using a nominal operating point, to ensure stability of the loop at that point. This was done in the companion design https://www.systemvision.com/design/laser-temperature-regulator-tdfs. But because many of the components in this loop are non-linear in nature (e.g. the TEC, thermistor, even the op-amp with rail voltage limiting), it is good practice to use simulation to verify performance during large-signal transients.

Calibrate TEC/TEG for Energy Harvesting

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

Swept R-load circuit to calibrate a thermoelectric generator model (TEG)

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

Thermoelectric Energy Harvesting using Peltier TEG

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Laser Temperature Regulator TDFS

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs