Mechatronics | PartQuest™ Explore

Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28

Designer229856

Member for

5 years 11 months

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Three Phase Power System - on Wed, 02/12/2020 - 15:45

Designer229715

Member for

5 years 11 months

11

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Copy of Automotive Electrical Power Distribution System - on Tue, 02/11/2020 - 18:51

Designer134136

Member for

8 years 6 months

4

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

ePower_820

Designer152721

Member for

8 years 3 months

109

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Copy of PID Speed Control Loop - Switching - for powerpoint

Designer10

Member for

12 years 2 months

625

designs

10

groups

Big fan of VHDL-AMS

Description

This example shows a more detailed circuit- and logic-level implementation of the PID Control Loop shown in the companion example, “PID Speed Control Loop – Continuous”. The ideal motor drive block of the “Continuous” version is expanded here, to include both a H-bridge motor drive, and also the digital logic necessary for converting the continuous PID controller output into the desired PWM signals that are distributed to drive the gates of the power MOSFET switches. The MOSFET model was calibrated to represent an IRF3710, using only information published on the manufacturer’s datasheet.The rest of the system, including the PID block-diagram controller, the mechanical fan load and the DC Motor characterized to represent an FRC CIM Motor, are the same as in the Continuous version. While the simulation time for this switching version is significantly longer, more detailed information about practical circuit performance and component sizing is available. For example, the fan speed step response is somewhat different from the conceptual design, because of the losses in the MOSFETs under high current conditions, as well as voltage drop in the battery. Also, information regarding component stress levels within the “datasheet specified” MOSFETs and Diodes is provided.

About text formats

Copy of Three Phase Power System - on Tue, 01/28/2020 - 08:36

Designer10

Member for

12 years 2 months

625

designs

10

groups

Big fan of VHDL-AMS

Description

About text formats

Copy of PID Speed Control Loop - Switching - on Mon, 01/27/2020 - 21:01

Designer229245

Member for

5 years 11 months

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a more detailed circuit- and logic-level implementation of the PID Control Loop shown in the companion example, “PID Speed Control Loop – Continuous”. The ideal motor drive block of the “Continuous” version is expanded here, to include both a H-bridge motor drive, and also the digital logic necessary for converting the continuous PID controller output into the desired PWM signals that are distributed to drive the gates of the power MOSFET switches. The MOSFET model was calibrated to represent an IRF3710, using only information published on the manufacturer’s datasheet.The rest of the system, including the PID block-diagram controller, the mechanical fan load and the DC Motor characterized to represent an FRC (First Robotics Competition) CIM Motor, are the same as in the Continuous version. While the simulation time for this switching version is significantly longer, more detailed information about practical circuit performance and component sizing is available. For example, the fan speed step response is somewhat different from the conceptual design, because of the losses in the MOSFETs under high current conditions, as well as voltage drop in the battery. Also, information regarding component stress levels within the “datasheet specified” MOSFETs and Diodes is provided.

About text formats

Three Phase Power System

Designer220281

Member for

6 years 6 months

12

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Three Phase Power System

Designer220281

Member for

6 years 6 months

12

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

PID Speed Control Loop - Switching

Designer227945

Member for

6 years 1 month

8

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows a more detailed circuit- and logic-level implementation of the PID Control Loop shown in the companion example, “PID Speed Control Loop – Continuous”. The ideal motor drive block of the “Continuous” version is expanded here, to include both a H-bridge motor drive, and also the digital logic necessary for converting the continuous PID controller output into the desired PWM signals that are distributed to drive the gates of the power MOSFET switches. The MOSFET model was calibrated to represent an IRF3710, using only information published on the manufacturer’s datasheet.The rest of the system, including the PID block-diagram controller, the mechanical fan load and the DC Motor characterized to represent an FRC (First Robotics Competition) CIM Motor, are the same as in the Continuous version. While the simulation time for this switching version is significantly longer, more detailed information about practical circuit performance and component sizing is available. For example, the fan speed step response is somewhat different from the conceptual design, because of the losses in the MOSFETs under high current conditions, as well as voltage drop in the battery. Also, information regarding component stress levels within the “datasheet specified” MOSFETs and Diodes is provided.

About text formats

Troubleshooting Terms of Use Cookie Notice Data Privacy Notice