Mechatronics | PartQuest™ Explore

Copy of LVDT Position Sensing System - on Fri, 07/07/2023 - 14:20

Designer247277

Member for

2 years 6 months

9

designs

1

groups

Welcome to the community!!

Description

A Linear Variable Differential Transformer (LVDT) and analog signal conditioning circuit are used for a position sensing system. An oscillator provides a sinusoidal excitation signal to the primary winding of the LVDT. The differential secondary winding outputs are rectified and low-pass filtered. The difference voltage, which is proportional to the mechanical displacement of the LVDT core, is the measurement result.

This virtual prototype can be used to select the low pass filter frequency, so it is low enough that the oscillation frequency is mostly removed from the output signal, yet high enough to track the natural frequency of mechanical system the sensor is intended to measure. It can also be used to analyze parasitic effects, such as the resistance of the wires connecting the sensor to the signal conditioning circuits. This resistance affects the output voltage and therefore corrupts the measurement results. Likewise, the non-linear behavior of the rectifier diodes affects the linearity of the position measurement.This can be seen if the force input is slowly ramped from -1000N to 1000N over a 1 second interval.

About text formats

Copy of Loudspeaker with Simple Amplifier - on Wed, 07/05/2023 - 10:31

Designer247277

Member for

2 years 6 months

9

designs

1

groups

Welcome to the community!!

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Loudspeaker with Simple Amplifier - on Wed, 07/05/2023 - 10:31

Designer247277

Member for

2 years 6 months

9

designs

1

groups

Welcome to the community!!

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

ServoDC_PID_continuo

Designer242728

Member for

4 years

4

designs

1

groups

I'm a member of the PartQuest Explore community.

ServoDC_PID_continuo

Designer242728

Member for

4 years

4

designs

1

groups

I'm a member of the PartQuest Explore community.

Copy of project2 - on Wed, 03/24/2021 - 20:17

Designer238037

Member for

4 years 11 months

14

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

project2

Designer238108

Member for

4 years 11 months

10

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

F_dip

Designer238037

Member for

4 years 11 months

14

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

My test

Designer21

Member for

12 years 2 months

104

designs

3

groups

Member of the PartQuest Explore team.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats