PartQuest Explore Promote

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This LED lighting example demonstrates the value of simulating both the electrical and thermal aspects of power dissipating circuits together, simultaneously.In this application example, a Vishay NTCS0402 Thermistor provides feedback of the enclosure temperature. This feedback is used to control PWM dimming of the LEDs, thereby limiting the internal temperature when operating at high external ambient temperature conditions.This is a "Live" design, the user can change key parameter values and then run new simulations to see the results. These parameters include "r_mirror", the resistance of the current mirror that controls the capacitor charging rate of the 555 timer, and thereby sets the PWM frequency*. The user can also change "r_offset" that controls the temperature level at which the dimming operation begins. Finally, the user can set "r_iLED_set", to control the ON-state operating current of the LEDs.*Note: The PWM switching frequency was intentionally reduced from the practical value of 260 Hz to 2.6 Hz, in order to provide fast simulations and realistic (long) thermal time constants. This was accomplished by increasing the 555 timer capacitor from 100 nF to 10 uF. This should have no significant impact on the thermal feedback or settling behavior that would be observed at the higher PWM frequencies needed to avoid visual "flicker" to the human eye (i.e. &gt; 200 Hz).

simplified LED Driver with Auto-Dimming - Low PWM frequency but realistic thermal time constants

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This LED lighting example demonstrates the value of simulating both the electrical and thermal aspects of power dissipating circuits together, simultaneously.In this application example, a Vishay NTCS0402 Thermistor provides feedback of the enclosure temperature. This feedback is used to control PWM dimming of the LEDs, thereby limiting the internal temperature when operating at high external ambient temperature conditions.This is a "Live" design, the user can change key parameter values and then run new simulations to see the results. These parameters include "r_mirror", the resistance of the current mirror that controls the capacitor charging rate of the 555 timer, and thereby sets the PWM frequency*. The user can also change "r_offset" that controls the temperature level at which the dimming operation begins. Finally, the user can set "r_iLED_set", to control the ON-state operating current of the LEDs.*Note: The PWM switching frequency was intentionally reduced from the practical value of 260 Hz to 2.6 Hz, in order to provide fast simulations and realistic (long) thermal time constants. This was accomplished by increasing the 555 timer capacitor from 100 nF to 10 uF. This should have no significant impact on the thermal feedback or settling behavior that would be observed at the higher PWM frequencies needed to avoid visual "flicker" to the human eye (i.e. &gt; 200 Hz).

LED Driver with Auto-Dimming - Low PWM frequency but realistic thermal time constants

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This LED lighting example demonstrates the value of simulating both the electrical and thermal aspects of power dissipating circuits together, simultaneously.In this application example, a Vishay NTCS0402 Thermistor provides feedback of the enclosure temperature. This feedback is used to control PWM dimming of the LEDs, thereby limiting the internal temperature when operating at high external ambient temperature conditions.This is a "Live" design, the user can change key parameter values and then run new simulations to see the results. These parameters include "r_mirror", the resistance of the current mirror that controls the capacitor charging rate of the 555 timer, and thereby sets the PWM frequency*. The user can also change "r_offset" that controls the temperature level at which the dimming operation begins. Finally, the user can set "r_iLED_set", to control the ON-state operating current of the LEDs.*Note: The PWM switching frequency was intentionally reduced from the practical value of 260 Hz (used in the companion design https://www.systemvision.com/design/led-driver-auto-dimming-thermal-protection), to 2.6 Hz, in order to provide fast simulations and realistic (long) thermal time constants. This was accomplished by increasing the 555 timer capacitor from 100 nF to 10 uF. This should have no significant impact on the thermal feedback or settling behavior that would be observed at the higher PWM frequencies needed to avoid visual "flicker" to the human eye (i.e. &gt; 200 Hz).

LED Driver with Auto-Dimming for Thermal Protection

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This LED lighting example demonstrates the value of simulating both the electrical and thermal* aspects of power dissipating circuits together, simultaneously.

In this application example, a Vishay NTCS0603 Thermistor provides feedback of the enclosure temperature. This feedback is used to control PWM dimming of the LEDs, thereby limiting the internal temperature when operating at high external ambient temperature conditions.

This is a "Live" design, the user can change key parameter values and then run new simulations to see the results. These parameters include "r_mirror", the resistance of the current mirror that controls the capacitor charging rate of the 555 timer, and thereby set the PWM frequency. The user can also change "r_offset" that controls the temperature level at which the dimming operation begins. Finally, the user can set "r_iLED_set", to control the ON-state operating current of the LEDs.

----------------

* To reduce the time needed to simulate the transition and settling at 6 different temperature levels, all thermal time constants were reduced by approximately 1000x. The actual thermal response time constant of the NTCS0603 is approximately 3 seconds (depends on mounting), not 3 msec! Also, the enclosure thermal capacitance value would more likely be 3 (J/degC) instead of 3 (mJ/degC), giving a thermal time constant for the enclosure of 10 (degC/Watt) * 3 (J/degC) = 30 seconds. This time scaling does not affect the static relationship between the outside temperature and PWM dimming.

LED Driver with Auto-Dimming for Thermal Protection- Alain

alain stas
Designer208121

alain stas

Member for

5 years 11 months

113

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

Laser Temperature Regulator using Peltier TEC and Vishay Thermistor

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This "Live Application" example shows the ability of a Peltier Module, or Thermo-Electric Cooler (TEC), to actively transfer heat away from a "laser" or other electronic device, during fast-changing power dissipation conditions. A Vishay thermistor from our Partner Library, with resistance that is sensitive to temperature, is used in a Wheatstone Bridge configuration. It produces a differential voltage that is amplified by an op-amp circuit. The op-amp output voltage is approximately proportional to temperature.The rest of the control loop is modeled here using ideal mathematical control blocks. This abstraction allows the designer to focus on the overall performance of the regulator, and to assess the choice of PID gains during actual transient operation.All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance of the "laser", which is just a simple resistance heating element for this example, to change the power dissipation level. You can also change the heat transfer resistance values in the thermal network, to see their effect on system performance. Finally, you can change the PID control block gains and see the effect on the steady-state and transient behavior of this temperature regulation system.Note: You can move the waveform probes to see any other signal in the system.

Laser Temperature Regulator using Peltier TEC

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

designs