Switching Converter | PartQuest™ Explore

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

SMSSA Theory - Test rev 2

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

SMSSA Theory Test

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Buck DC to DC Converter - save and regenerate waveforms

UCM
Designer207769

UCM

Member for

5 years 11 months

13

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a copy of Mike Donnelly's Buck DC to DC Converter modified to demonstrate data reduction for downloaded waveforms. For more information about the buck converter you can find Mike's design athttps://www.systemvision.com/design/buck-dc-dc-converter-switchingThis design ramps up internal voltages for a simplified model of softstart. Mike's load transient is timed to activate after steady state. The L1 current rises after an initial spike. This current charges the output cap to generate a rising output voltage. That output voltage rises past the 5V setpoint until steady state sets in around 5.5V. After that Vout settles back to its steady state level. The load transient triggers disturbances in Vout at both edges of the transient.For further analysis of steady state and line/load transients, an x-sampling voltage source is added to reduce the size of the .csv data and to skip over startup. Data reduced files are generated in an Excel post-processing session based on the x-sampling voltage peaks.The reduced data can be read back into SystemVision or other appllications to display the waveforms,compare them to waveforms from another source or use them as sources in further simulations.

About text formats

Switch Mode Small Signal Analysis - Filter Bypassed

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Switch Mode Small Signal Analysis - ripple extraction

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Norm's TDFS Exercise - window averaging topology rev2

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Norm's TDFS Exercise - experimental

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,697

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Buck DC to DC Converter - Switching

Darrell
Designer10

Darrell

Member for

11 years

624

designs

10

groups

Big fan of VHDL-AMS

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Buck DC to DC Converter vs. Linear Regulator”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensators, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients, ripple rejection and the power consumption are very similar to the results from the abstract model.This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVBA130LT3G) and op-amps (NCV20071), as well as the passive inductor (MSS1583-105KE_) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models. For example, the stress indicator for the power inductor shows that the maximum RMS current level is exceeded under this simulated operating condition (i.e. stress_ratio_current_rms &gt; 1.0).The companion design, "TDFS Loop Stability for Buck DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

RobertDavisDesigner256

Member for

NormDesigner43361

Member for

NormDesigner43361

Member for

NormDesigner43361

Member for

UCMDesigner207769

Member for

NormDesigner43361

Member for

NormDesigner43361

Member for

NormDesigner43361

Member for

Mike DonnellyDesigner19

Member for

DarrellDesigner10

Member for

RobertDavis
Designer256

Norm
Designer43361

Norm
Designer43361

Norm
Designer43361

UCM
Designer207769

Norm
Designer43361

Norm
Designer43361

Norm
Designer43361

Mike Donnelly
Designer19

Darrell
Designer10