Step-Down | PartQuest™ Explore

Application Area

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,697

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Norm's TDFS Exercise - Mike's topology

Norm
Designer43361

Norm

Member for

8 years 7 months

328

designs

2

groups

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

TDFS Loop Stability for Step-Down DC to DC (Buck) Converter - Switching

Devon Johnson
Designer250

Devon Johnson

Member for

9 years 7 months

49

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

TDFS Impedance Stability of Transmission Line Fed LED Driver - Switching

MASA
Designer208

MASA

Member for

9 years 9 months

579

designs

8

groups

Description

This example demonstrates the use of the TDFS method (Time Domain Frequency Sweep) to measure impedance stability ratio. The system is a switching DC/DC step-down power converter used for LED lighting, supplied by a battery through a long power cable.The TDFS impedance stability measurement model applies a 0.2A sinusoidal stimulus current at the point where the cable connects to the converter. The voltage at that point, as well as the stimulus current splits (toward the source and the load) are measured, and the associated source and load impedances vs. frequency are computed.The ratio of the source to load impedance is the impedance stability ratio (Tm). Similar to the open-loop frequency response requirement for closed-loop stability, Tm must not have magnitude = 1.0 at phase = 180 degrees, at any frequency.For this system, with a cable length of 400 meters and 8 AWG wire, the results show that the impedance ratio magnitude (green waveform) reaches unity (0 dB) at close to 2 kHz, where the phase (light blue waveform) is approximately 165 degress. This implies a "phase margin" of only 15 degrees, For a longer cable, this margin is further reduced. As shown in the companion example, "Transmission Line Fed LED Driver - Switching", for the cable length = 800 meters the system is unstable.This instability is the result of the "source" impedance (which includes the cable) variation over frequency, interacting with the varying load impedance. Note that at low frequency, the load effectively has a negative impedance, due to the constant power nature of the DC to DC converter.

About text formats

Transmission Line Fed LED Driver - Switching

KwangabaSafari
Designer123756

KwangabaSafari

Member for

7 years 6 months

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example illustrates the challenging problem of operating a DC/DC converter at the end of a long cable or transmission line. In this case, a set of three LEDs are co-located with a Step-Down (Buck) switching converter, Together the LEDs consume 25W at 6VDC, and they are supplied by an 18V battery at the other end of an 800 meter cable. The simulation results indicate that the circuit operates properly with only one LED turned-on, but becomes unstable with the other two LEDs are switched on at 1 ms.The transmission line model is specified to use 16 coupled RLC lumped segments, each representing 50 meters of cable length. The conductor DC resistance is set to 1 mOhm/meter, corresponding to 5 AWG wire. This should result in a relatively small voltage drop at the expected 1.5A current needed to support the load. But the effect of the transmission line is more than the DC resistance. The effective impedance and propagation delay, combined with the effective negative impedance of the power converter (i.e. constant power load), result in an unstable power system interaction.You can try using a reduced cable length (e.g. 400 meters, 8 AWG = 2.1 mOhm/meter, or 100 meters, 14 AWG = 8.3 mOhm/meter) by making a copy of this design and re-running the simulation. You will see that the circuit performance is greatly improved with a shorter cable.The concept of Impedance Stability Ratio, and the ability to measure it using SystemVision's TDFS (Time Domain Frequency Sweep) method, will be demonstrated in a related design example and discussed in Part 3 of the TDFS Blog Series, both coming soon!

About text formats

TDFS Loop Stability for Step-Down DC to DC (Buck) Converter - Switching

BirolELK
Designer27861

BirolELK

Member for

8 years 9 months

3

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

TDFS Loop Stability for Step-Down DC to DC (Buck) Converter - Switching

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,697

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

Mike DonnellyDesigner19

Member for

NormDesigner43361

Member for

Devon JohnsonDesigner250

Member for

MASADesigner208

Member for

KwangabaSafariDesigner123756

Member for

BirolELKDesigner27861

Member for

Mike DonnellyDesigner19

Member for

Mike Donnelly
Designer19

Norm
Designer43361

Devon Johnson
Designer250

MASA
Designer208

KwangabaSafari
Designer123756

BirolELK
Designer27861

Mike Donnelly
Designer19