PWM | PartQuest™ Explore

mosfet-switching-design-pmsm-inf100A

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

mosfet-switching-design-pmsm-buk100A

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

mosfet-switching-design-bldc-buk100A

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

mosfet-switching-design-bldc-on100A

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

Copy of Power PWM driver with voltage controlled current source - on Sun, 01/17/2021 - 19:44

Designer

Description

Power PWM driver with voltage controlled current source for driving/suppling pulse transformer.

Pulse transformer parameters:

1. INPUT COIL:

1.1. fi wire enamelled winding = 0,35 mm (from pulse transformer datasheet)

1.2. wire enamelled winding length = 0,400 m = 400 mm (calculated)

1.3. N = 2 x 12 scrolls (from pulse transformer datasheet)

1.4. R = 0,11 Ohms (parallel 2 x 0,22 Ohms) (measured and/equal calculated

1.5. H = 47,52 uH (from pulse transformer datasheet)

1.6. U = 3,5 - 15 V DC (from pulse transformer datasheet)

2. OUTPUT COIL:

2.1. fi wire enamelled winding = 0,15 mm (from pulse transformer datasheet)

2.2. N = 1 x 300 scrolls (from pulse transformer datasheet)

2.3. R = 10,6 Ohms (measured)

2.4. U = 400 V DC (after diode one-half rectifier and C filter) (from pulse transformer datasheet)

3. OTHER

3.1. voltage insulation test at 1 kV (from pulse transformer datasheet)

3.2. dedicated frequency 33 kHz (from pulse transformer datasheet)

3.3. recommended driver IC ON Semiconductor MC34063 (1.5 A, Step-Up/Down/Inverting Switching Regulators) (from pulse transformer datasheet)

Parameters to reach:

1. PWM frequency: from 1 kHz to 75/100 kHz

2. PWM Duty Cycle: from 5 % to 95 %

3. Current: from 5/10 mA DC to 1000/2000 mA DC

4. PWM control voltage: from 0 V DC to 3.0 V DC or from 0 V DC to 3.3 V DC (whatever for now)

5. Current source voltage: from 0.1 V DC to +3.3/5.0 V DC

About text formats

mosfet-switching-compare-simpl-inf

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

Copy of mosfet-switching-design-bldc-inf100A

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

mosfet-switching-compare-simpl-on

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

mosfet-switching-compare-on

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

Copy of mosfet-switching-compare-inf

Designer

Description

This design is similar to the design "Ideal Switching Design for Moog PMSM - BLDC Motor Use-Case", but the ideal switches in the inverter are replaced with "Datasheet" Power MOSFET models. These models are calibrated to match the datasheet specified characteristics of an STW45NM50 device. This replacement required the conversion to the digital signals used to control the switch states, to actual gate voltages. So representative models of the necessary gate drivers were also added.

In addition, a "hot part monitor" model was added to one of the Power MOSFETs. This models the datasheet specified "Rthj_amb" (0.32 degrees C per Watt), in order to predict the internal junction temperature during different phases of inverter operation. A thermal time-constant of 1 ms was assumed, which may be quite unrealistic. It is possible to add much higher fidelity thermal network models of the heat transfer path if valid parameters are given.

Finally, one of the low-pass filters used in the current sense path was changed to reflect a possible circuit implementation using op-amps. This is to show the ability to move seamlessly between ideal signal-flow (or continuous transfer function block) modeling to circuit implementation modeling, anywhere in a system design.

You can also see a version of this design that uses the manufacturer provided SPICE model for the Power MOSFET: "STW45NM50 MOSFET Switching Design for Moog PMSM - BLDC Motor Use-Case"

About text formats

Troubleshooting Terms of Use Cookie Notice Data Privacy Notice