Mechanical Resonance | PartQuest™ Explore

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of Kinetic Energy Harvesting - on Mon, 08/26/2024 - 18:10

mike.jensen
Designer244302

mike.jensen

Member for

1 year 11 months

21

designs

1

groups

I'm a member of the PartQuest Explore community.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of Kinetic Energy Harvesting - on Tue, 04/02/2024 - 20:24

Designer0

Member for

4 years 8 months

0

designs

0

groups

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of Kinetic Energy Harvesting - on Wed, 07/26/2023 - 06:42

User-1690346477
Designer247966

User-1690346477

Member for

1 year 1 month

1

designs

1

groups

Welcome to the community!!

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of Kinetic Energy Harvesting - on Sun, 03/14/2021 - 17:00

br43556
Designer238668

br43556

Member for

3 years 6 months

0

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of boost converter average model open loop - on Wed, 02/24/2021 - 20:39

Mike Donnelly
Designer19

Mike Donnelly

Member for

10 years 10 months

1,652

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

boost converter average model open loop

Darrell
Designer10

Darrell

Member for

10 years 10 months

624

designs

10

groups

Big fan of VHDL-AMS

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

Boost converter average model

Darrell
Designer10

Darrell

Member for

10 years 10 months

624

designs

10

groups

Big fan of VHDL-AMS

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

TEST STAGE Kinetic Energy Harvesting

Galina
Designer21

Galina

Member for

10 years 10 months

104

designs

3

groups

Member of the PartQuest Explore team.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Copy of Kinetic Energy Harvesting - on Tue, 11/10/2020 - 20:11

jupryhamzah
Designer229733

jupryhamzah

Member for

4 years 7 months

6

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for kinetic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The design contains mechanical, magnetic and electronic circuit elements, with energy conservation and cross-discipline dynamic interactions automatically included in the system model. The user can directly specify the physical or behavioral characteristics of many of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross sectional area of the magnetic core, the number of winding turns, the resistor and capacitor values, as well as the drop-out voltage of the linear regulator.

In the nominal simulation results displayed on the schematic, the upper right waveform viewer shows the initial start-up of the system, with the amplitude of the external vibration source of 0.07 mm peak at 60 Hz, equivalent to a peak acceleration of 1 g. The nominal armature spring-mass resonance frequency is 60 Hz, and the armature displacement is seen to reach the frame's travel limit of 10 mm peak-to-peak!

In the upper left, the waveform viewer is zoomed-in near the 1 sec. simulation time mark. It shows the time-varying core flux density and winding voltage, as the two air-gaps expand and contract with armature displacement, rapidly changing the magnetic flux path's effective reluctance value. In the lower right waveform viewer, the DC output voltage from the Schottky diode full-wave rectifier and the linear regulator output voltage are observed. The periodic disturbance is caused by the switched load being applied to the system.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

Mike DonnellyDesigner19

Member for

mike.jensenDesigner244302

Member for

Designer0

Member for

User-1690346477Designer247966

Member for

br43556Designer238668

Member for

Mike DonnellyDesigner19

Member for

DarrellDesigner10

Member for

DarrellDesigner10

Member for

GalinaDesigner21

Member for

jupryhamzahDesigner229733

Member for

Mike Donnelly
Designer19

mike.jensen
Designer244302

User-1690346477
Designer247966

br43556
Designer238668

Mike Donnelly
Designer19

Darrell
Designer10

Darrell
Designer10

Galina
Designer21

jupryhamzah
Designer229733