magnetic saturation | PartQuest™ Explore

Application Area

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years

1,700

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Tue, 10/13/2020 - 10:52

Sorin
Designer203848

Sorin

Member for

6 years 1 month

53

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.

You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.

You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.

Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.

It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Thu, 10/01/2020 - 20:51

ikguy
Designer7846

ikguy

Member for

9 years

12

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.

You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.

You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.

Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.

It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Tue, 08/18/2020 - 15:36

khaled.elgeneidy
Designer233792

khaled.elgeneidy

Member for

4 years 3 months

19

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.

You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.

You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.

Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.

It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Fri, 06/19/2020 - 15:21

MASA
Designer208

MASA

Member for

9 years 9 months

579

designs

8

groups

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.

You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.

You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.

Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.

It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Fri, 04/10/2020 - 17:16

dmoctezu
Designer230982

dmoctezu

Member for

4 years 7 months

4

designs

1

groups

Electronic and science enthusiast!!!

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.

You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.

You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.

Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.

It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Copy of Transformer Magnetizing In-rush Current - on Fri, 02/21/2020 - 14:40

h.agdn335
Designer229880

h.agdn335

Member for

4 years 9 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This transformer design example demonstrates a current in-rush or "peaking" effect that depends on the phase or timing of the AC supply switch closure. A rather counter-intuitive result is shown;

Case 1: Set the initial_delay of the digital pulse to 4.17m seconds, which causes the switch to closed when the sinusoidal AC line input voltage is at its peak, one quarter-cycle at its 60 Hz frequency. The current into the primary winding will immediately follow its nominal steady-state no-load profile, with a peak of just under 100mA.

Case 2: Set the digital pulse initial_delay to 0 seconds, so that the line voltage is applied to the transformer immediately at its rising zero-crossing. This results in a large non-sinusoidal peaking current which exceeds 500mA on its initial cycle!

This is a direct result of saturation in the magnetic core. To produce the necessary "volt-seconds" in Case 2, the magnetic flux in the core must be twice that of Case 1. But if the transformer is sized such that its peak flux density is somewhat close to the the saturation level for nominal steady-state operation, then a start-up transient with the unfortunate timing of Case 2 will result in a large in-rush current.

Note that the flux density "b" is displayed for the magnetic core. The core saturation flux density is specified as 1.5 Tesla, a typical value for Electrical Steel. You can also select "B vs. H from Table" to see the performance for a specific type of NGO Electrical Steel -35PN250 from the manufacturer Posco.

About text formats

Copy of Inductor Model using Magnetic Circuit Modeling Method - on Sat, 02/15/2020 - 11:33

mgsb275
Designer229768

mgsb275

Member for

4 years 9 months

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed.You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Transformer Magnetizing In-rush Current

Darrell
Designer10

Darrell

Member for

11 years

624

designs

10

groups

Big fan of VHDL-AMS

Description

This transformer design example demonstrates a current in-rush or "peaking" effect that depends on the phase or timing of the AC supply switch closure. A rather counter-intuitive result is shown;Case 1: Set the initial_delay of the digital pulse to 4.17m seconds, which causes the switch to closed when the sinusoidal AC line input voltage is at its peak, one quarter-cycle at its 60 Hz frequency. The current into the primary winding will immediately follow its nominal steady-state no-load profile, with a peak of just under 100mA. Case 2: Set the digital pulse initial_delay to 0 seconds, so that the line voltage is applied to the transformer immediately at its rising zero-crossing. This results in a large non-sinusoidal peaking current which exceeds 500mA on its initial cycle!This is a direct result of saturation in the magnetic core. To produce the necessary "volt-seconds" in Case 2, the magnetic flux in the core must be twice that of Case 1. But if the transformer is sized such that its peak flux density is somewhat close to the the saturation level for nominal steady-state operation, then a start-up transient with the unfortunate timing of Case 2 will result in a large in-rush current.Note that the flux density "b" is displayed for the magnetic core. The core saturation flux density is specified as 1.5 Tesla, a typical value for Electrical Steel. You can also select "B vs. H from Table" to see the performance for a specific type of NGO Electrical Steel -35PN250 from the manufacturer Posco.

About text formats

Inductor Model using Magnetic Circuit Modeling Method

瀧澤登
Designer123146

瀧澤登

Member for

7 years 7 months

365

designs

3

groups

Description

This example shows that you can build an inductor model from magnetic components (i.e. a winding and a core), and with an air-gap if needed. You can run the nominal simulation with n = 23 turns on the winding, with the core model state set to "Linear" and a near-zero air-gap. The current transient in the winding matches the current in an ideal inductor model, both are representative of 1mH inductance. But in that configuration, the flux density "b" in the core is over 1.8 Tesla, well beyond the limits of a ferrite material.You can set the magnetic core to "Non-linear with Saturation", and note that the saturation level is 525mT for the modeled core material. Then you can re-run the simulation to see the actual current profile that would result from this more realistic core behavior.Finally, set the number of winding turns to 96. Then set the air-gap to 0.25mm, instead of the nominal 0.25um. This will restore the current rise profile that is expected for a 1mH inductor, but also keep the flux density in the core below the 525mT level.It is also instructive to observe the energy stored in the ideal inductor, as well as the magnetic core and the air-gap, in each of the cases above.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

Mike DonnellyDesigner19

Member for

SorinDesigner203848

Member for

ikguyDesigner7846

Member for

khaled.elgeneidyDesigner233792

Member for

MASADesigner208

Member for

dmoctezuDesigner230982

Member for

h.agdn335Designer229880

Member for

mgsb275Designer229768

Member for

DarrellDesigner10

Member for

瀧澤登Designer123146

Member for

Mike Donnelly
Designer19

Sorin
Designer203848

ikguy
Designer7846

khaled.elgeneidy
Designer233792

MASA
Designer208

dmoctezu
Designer230982

h.agdn335
Designer229880

mgsb275
Designer229768

Darrell
Designer10

瀧澤登
Designer123146