Copy of Loudspeaker with Simple Amplifier - on Sat, 09/12/2020 - 13:55 pdhobby1213Designer234706 × pdhobby1213 Member for 3 years 6 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby pdhobby1213 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/340364"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/340364"></iframe> Share a Link Copy URL https://explore.partquest.com/node/340364 Copy of Loudspeaker with Simple Amplifier - on Fri, 09/11/2020 - 01:32 pdhobby1213Designer234706 × pdhobby1213 Member for 3 years 6 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby pdhobby1213 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/340012"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/340012"></iframe> Share a Link Copy URL https://explore.partquest.com/node/340012 Copy of Loudspeaker with Simple Amplifier - on Wed, 08/19/2020 - 15:31 aungtunDesigner211422 × aungtun Member for 5 years 1 month 9 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby aungtun × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/334023"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/334023"></iframe> Share a Link Copy URL https://explore.partquest.com/node/334023 Copy of Loudspeaker with Simple Amplifier - on Thu, 07/30/2020 - 14:49 ghassanawada125Designer233622 × ghassanawada125 Member for 3 years 7 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby ghassanawada125 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329868"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329868"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329868 Loudspeaker with Simple Amplifier - on Mon, 07/27/2020 - 16:40 andre02crisDesigner233577 × andre02cris Member for 3 years 8 months 4 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby andre02cris × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329199"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329199"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329199 Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Fri, 09/11/2020 - 01:32 pdhobby1213Designer234706 × pdhobby1213 Member for 3 years 6 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby pdhobby1213 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/340012"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/340012"></iframe> Share a Link Copy URL https://explore.partquest.com/node/340012 Copy of Loudspeaker with Simple Amplifier - on Wed, 08/19/2020 - 15:31 aungtunDesigner211422 × aungtun Member for 5 years 1 month 9 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby aungtun × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/334023"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/334023"></iframe> Share a Link Copy URL https://explore.partquest.com/node/334023 Copy of Loudspeaker with Simple Amplifier - on Thu, 07/30/2020 - 14:49 ghassanawada125Designer233622 × ghassanawada125 Member for 3 years 7 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby ghassanawada125 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329868"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329868"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329868 Loudspeaker with Simple Amplifier - on Mon, 07/27/2020 - 16:40 andre02crisDesigner233577 × andre02cris Member for 3 years 8 months 4 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby andre02cris × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329199"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329199"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329199 Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Wed, 08/19/2020 - 15:31 aungtunDesigner211422 × aungtun Member for 5 years 1 month 9 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby aungtun × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/334023"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/334023"></iframe> Share a Link Copy URL https://explore.partquest.com/node/334023 Copy of Loudspeaker with Simple Amplifier - on Thu, 07/30/2020 - 14:49 ghassanawada125Designer233622 × ghassanawada125 Member for 3 years 7 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby ghassanawada125 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329868"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329868"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329868 Loudspeaker with Simple Amplifier - on Mon, 07/27/2020 - 16:40 andre02crisDesigner233577 × andre02cris Member for 3 years 8 months 4 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby andre02cris × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329199"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329199"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329199 Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Thu, 07/30/2020 - 14:49 ghassanawada125Designer233622 × ghassanawada125 Member for 3 years 7 months 2 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby ghassanawada125 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329868"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329868"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329868 Loudspeaker with Simple Amplifier - on Mon, 07/27/2020 - 16:40 andre02crisDesigner233577 × andre02cris Member for 3 years 8 months 4 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby andre02cris × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329199"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329199"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329199 Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Loudspeaker with Simple Amplifier - on Mon, 07/27/2020 - 16:40 andre02crisDesigner233577 × andre02cris Member for 3 years 8 months 4 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby andre02cris × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/329199"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/329199"></iframe> Share a Link Copy URL https://explore.partquest.com/node/329199 Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Tue, 06/30/2020 - 08:11 bedrosian1134Designer198997 × bedrosian1134 Member for 5 years 10 months 58 designs 4 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby bedrosian1134 × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/325625"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/325625"></iframe> Share a Link Copy URL https://explore.partquest.com/node/325625 Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Mon, 06/22/2020 - 17:10 blipssDesigner232660 × blipss Member for 3 years 9 months 2 designs 2 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby blipss × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/324446"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/324446"></iframe> Share a Link Copy URL https://explore.partquest.com/node/324446 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316734"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316734"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316734 Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Tue, 05/26/2020 - 08:15 farhad.pirvaliDesigner232069 × farhad.pirvali Member for 3 years 10 months 0 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby farhad.pirvali × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/316733"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/316733"></iframe> Share a Link Copy URL https://explore.partquest.com/node/316733 Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››
Copy of Loudspeaker with Simple Amplifier - on Wed, 02/19/2020 - 17:28 vleckenDesigner229856 × vlecken Member for 4 years 1 month 1 designs 1 groups Title Description <p>This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.</p> <p>A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.</p> <p>The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!</p> <p>All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.</p> <p>* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:</p> <p>https://www.systemvision.com/design/loudspeaker-only-frequency-response</p> About text formats Tags LoudspeakerAmplifierelectro-mechanical resonanceBDP947NCV20071 Op-AmpBDP947 NPN TransistorMechatronicsmagnetic actuator Select a tag from the list or create your own.Drag to re-order taxonomy terms. License - None - What's this? Design Titleby vlecken × Embed Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/embed-design/282849"></iframe> Embed Live Design Copy Embed Code <iframe allowfullscreen="true" referrerpolicy="origin-when-cross-origin" frameborder="0" width="100%" height="720" scrolling="no" src="https://explore.partquest.com/node/282849"></iframe> Share a Link Copy URL https://explore.partquest.com/node/282849 Pagination Previous page ‹‹ Page 2 Next page ››