PartQuest Explore Promote

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

Transient Stability Testing of Transmission Line Fed LED Driver

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years 1 month

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

TDFS Impedance Stability of Transmission Line Fed LED Driver - Switching

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years 1 month

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the use of the TDFS method (Time Domain Frequency Sweep) to measure impedance stability ratio. The system is a switching DC/DC step-down power converter used for LED lighting, supplied by a battery through a long power cable.The TDFS impedance stability measurement model applies a 0.2A sinusoidal stimulus current at the point where the cable connects to the converter. The voltage at that point, as well as the stimulus current splits (toward the source and the load) are measured, and the associated source and load impedances vs. frequency are computed.The ratio of the source to load impedance is the impedance stability ratio (Tm). Similar to the open-loop frequency response requirement for closed-loop stability, Tm must not have magnitude = 1.0 at phase = 180 degrees, at any frequency.For this system, with a cable length of 400 meters and 8 AWG wire, the results show that the impedance ratio magnitude (green waveform) reaches unity (0 dB) at close to 2 kHz, where the phase (light blue waveform) is approximately 165 degress. This implies a "phase margin" of only 15 degrees, For a longer cable, this margin is further reduced. As shown in the companion example, "Transmission Line Fed LED Driver - Switching", for the cable length = 800 meters the system is unstable.This instability is the result of the "source" impedance (which includes the cable) variation over frequency, interacting with the varying load impedance. Note that at low frequency, the load effectively has a negative impedance, due to the constant power nature of the DC to DC converter.

LED Dimmer Circuit using 555 Timer

Mike Donnelly
Designer19

Mike Donnelly

Member for

11 years 1 month

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of Joule Thief Transformer Physical Design For LED Lighting - on Thu, 01/02/2025 - 19:41

User-1733240310
Designer260071

User-1733240310

Member for

1 month

2

designs

1

groups

Welcome to the community!!

Description

Copy of LED Dimmer Circuit using 555 Timer - on Thu, 12/26/2024 - 10:21

Designer0

Member for

4 years 11 months

0

designs

0

groups

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!