electro-mechanical resonance | PartQuest™ Explore

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Loudspeaker with Simple Amplifier

CReiman
Designer13936

CReiman

Member for

9 years

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Loudspeaker with Simple Amplifier

Jayne
Designer27

Jayne

Member for

11 years

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Loudspeaker with Simple Amplifier

Darrell
Designer10

Darrell

Member for

11 years 1 month

624

designs

10

groups

Big fan of VHDL-AMS

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Loudspeaker with Simple Amplifier

PacmeMagnin
Designer12106

PacmeMagnin

Member for

9 years

13

designs

1

groups

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0), making it obvious in this case that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Loudspeaker with Simple Amplifier

JosVelzquez
Designer12031

JosVelzquez

Member for

9 years

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0), making it obvious in this case that we need a bigger transistor!*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

DarrellDesigner10

Member for

DarrellDesigner10

Member for

DarrellDesigner10

Member for

DarrellDesigner10

Member for

YuliKosinovskyDesigner17956

Member for

CReimanDesigner13936

Member for

JayneDesigner27

Member for

DarrellDesigner10

Member for

PacmeMagninDesigner12106

Member for

JosVelzquezDesigner12031

Member for

Darrell
Designer10

Darrell
Designer10

Darrell
Designer10

Darrell
Designer10

YuliKosinovsky
Designer17956

CReiman
Designer13936

Jayne
Designer27

Darrell
Designer10

PacmeMagnin
Designer12106

JosVelzquez
Designer12031