Buck Converter

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

ePower_140

Designer152721

Member for

8 years 2 months

109

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

ePower_100

Designer152721

Member for

8 years 2 months

109

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Buck Converter Reference

Designer135501

Member for

8 years 6 months

61

designs

2

groups

Member of the PartQuest Explore team.

Designer135501

Member for

8 years 6 months

61

designs

2

groups

Member of the PartQuest Explore team.

Managing PWM Waveforms - Buck Converter

Designer43361

Member for

9 years 8 months

328

designs

2

groups

Description

To demonstrate data reduction in a PWM design I've copied and modified Mike Donnelly's Buck DC to DC Converter at https://www.systemvision.com/design/buck-dc-dc-converter-switchingI've added a simplified softstart to simulate startup. Sofstart is implemented by ramping up internal voltages over a 5ms period after a 0.5ms delay for a total startup time of 5.5ms. Mike's load transient is timed to activate after steady state. A line transient can be simulated by adding a pulsed voltage source in series with v_line.The total time to simulate startup, steady state and the load transient is set to 10.5ms of which only the final 4ms involve the response to the transient disturbance. Downloaded .csv files of the output voltage (v_out_buck), inductor current (l1inductor/i), or any other signal cover over 84,000 time points.For a 40us switching cycle, a 1us resolution samples each switching cycle 40 times and requires only 4,000 time points to cover the steady state and load transient response. A voltage source is included in the design to mark off this sampling resolution with a sawtooth signal that starts at 6.5ms. The sawtooth appears at the net named x_smpl. Downloading x_smpl along with v_out_buck to Excel enables edits that reduce the original 84,000 time points to 4,000.To demonstrate the data reduction technique for large .csv downloads,t he design includes a dedicated table voltage source which has been preloaded with a set of 4,000 samples from an earlier simulation. The voltage signal vout_reduced displays those 4,000 samples. The table voltage source can be edited to insert to store reduced data records of any transient response generated by this buck converter.Copies of the table voltage source can be placed into this or any other design in order to display the transient response or apply it to another simulation. This mechanism can be used to test designs that are driven by the buck converter output for their ability to withstand the transient disturbance. Other simulations can be used to compare the simulated response to measured data or to analyze the simulated transient response.Watch for an accompanying blog that will explain how the table voltage source works.

Buck Converter

Designer131621

Member for

8 years 6 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

TDFS Input Impedance of Step-Down (Buck) DC to DC Converter - Switching

Designer19

Member for

12 years 1 month

1,949

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the use of the TDFS method (Time Domain Frequency Sweep) to measure the input impedance of a switching DC/DC power converter. The converter circuit is identical to the design shown in the companion example: “Step-Down (Buck) DC to DC Converter - Switching”.In this example, the TDFS impedance measurement model applies a 12V DC bias to the line input, in addition to a sinusoidal stimulus with 3V peak amplitude, and a frequency range from 3 kHz to 30 kHz. The input current is measured and the impedance vs. frequency is computed. The results show that the impedance magnitude (blue waveform) is approximately 5.0 Ohms at low frequency, This is approximately the reflected value of the 1 Ohm load resistor, multiplied by the effective DC/DC conversion ratio squared: 1 Ohm * (12.0/5.0)**2 = 5.76 OhmThe phase measurement (red waveform) shows -175 degrees at low frequency, indicating that this is effectively a "negative resistance". That is, the input current decreases when the line voltage increases. This behavior can be observed directly in the time domain waveforms, where the line voltage (brown waveform) and the input current (green waveform) are almost completely out of phase at 3 kHz. This negative impedance, or constant power load characteristic, can be destabilizing in power distribution systems. This will be demonstrated in a related design, and in Part 3 of the TDFS Blog Series, coming soon!

TDFS Loop Stability for Step-Down DC to DC (Buck) Converter - Switching

Designer19

Member for

12 years 1 month

1,949

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example demonstrates the TDFS (Time Domain Frequency Sweep) Loop Stability Instrument Model. It is used to compute the open-loop transfer function of an operating (closed-loop) switching power converter. There is no need for state-average or continuous equivalent models for the modulator section of the design, as normally needed for frequency-domain (or "AC") analysis. Rather, the actual circuit component models can be used directly, because the open-loop transfer function is computed from time-domain simulation results.In this case, the converter is operating at 200kHz switching frequency, and is converting the 12V DC input to a regulated 5V output, while supplying a 5A current to the 1 Ohm load resistor. The TDFS measurement instrument indicates that the open-loop gain crossover frequency is at 26 kHz, and the phase margin is just under 60 degrees. This verifies that the opamp-based lead-lag compensator is providing adequate stability margin under these operating conditions.Note that the TDFS instrument model characterizes the open loop transfer function by injecting a small sinusoidal stimulus signal in series with the loop, and then measures the complex ratio of the return signal to the injected signal, is described in:D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries.The companion example, "Step-Down (Buck) DC to DC Converter - Switching", shows the line and load transient response of this converter design. Another companion example, "Step-Down (Buck) DC to DC Converter - Continuous", uses a state-average model of the switching (or modulator) section of the converter, so it supports traditional "AC" or frequency-domain analysis.

Step-Down (Buck) DC to DC Converter - Continuous

Designer19

Member for

12 years 1 month

1,949

designs

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description