Buck Converter | PartQuest™ Explore

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design uses both TDFS and standard AC Analysis methods to assess the stability of a closed-loop system. The design is the "Buck DC to DC Converter", using a state-average model for the modulator function.

The use of state-average models supports AC Analysis, but TDFS (Time Domain Frequency Sweep) is also used to show the equivalency of the methods. Note that the TDFS approach can be used for systems that do not support AC Analysis, such as switching circuits or systems that contain sampling or digital control aspects. This particular example is directly comparable to the design "TDFS Loop Stability for Buck DC to DC Converter - Switching". In that design, the TDFS method is used to measure the open loop transfer function of an operational switching circuit.

Note that the approach used to characterize the loop stability, by injecting a small sinusoidal stimulus signal in series with the loop and then measuring the complex ratio of the ground referenced return signal to the injected signal, is described in:

D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Tue, 08/25/2020 - 13:34

Designer234163

Member for

5 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Tue, 08/25/2020 - 10:29

Designer232513

Member for

5 years 5 months

18

designs

2

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

TDFS Sweep example

Designer234163

Member for

5 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design uses both TDFS and standard AC Analysis methods to assess the stability of a closed-loop system. The design is the "Buck DC to DC Converter", using a state-average model for the modulator function.

The use of state-average models supports AC Analysis, but TDFS (Time Domain Frequency Sweep) is also used to show the equivalency of the methods. Note that the TDFS approach can be used for systems that do not support AC Analysis, such as switching circuits or systems that contain sampling or digital control aspects. This particular example is directly comparable to the design "TDFS Loop Stability for Buck DC to DC Converter - Switching". In that design, the TDFS method is used to measure the open loop transfer function of an operational switching circuit.

Note that the approach used to characterize the loop stability, by injecting a small sinusoidal stimulus signal in series with the loop and then measuring the complex ratio of the ground referenced return signal to the injected signal, is described in:

D. Venable, “Testing Power Sources for Stability”, Venable technical paper #1, Venable Industries

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Tue, 08/25/2020 - 10:17

Designer232513

Member for

5 years 5 months

18

designs

2

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

Copy of C-6. Buck Converter Vo=250V Io=20A - on Wed, 08/19/2020 - 11:25

Designer234163

Member for

5 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Copy of C-7. Buck Converter 2-Phase Vo=250V Io=40A - on Wed, 08/19/2020 - 11:25

Designer234163

Member for

5 years 3 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Sat, 07/25/2020 - 11:01

Designer233541

Member for

5 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Sat, 07/18/2020 - 09:22

Designer30

Member for

11 years 11 months

188

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.

Copy of Step-Down (Buck) DC to DC Converter - Switching - on Sat, 07/18/2020 - 09:22

Designer30

Member for

11 years 11 months

188

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This design is a detailed circuit implementation of the more abstract "state-average" buck converter model shown in the companion design example: “Step-Down (Buck) DC to DC Converter - Continuous”. This example includes the low-pass voltage sense circuit, an op-amp implementation of the difference amplifier and the lead-lag compensator, as well as PWM switching control of a power MOSFET. Simulation results for the line and load transients are very similar to the results from the continuous model.

This design uses a number of "datasheet characterized" components, including the power MOSFET (MCH6337), freewheel diode (NRVTS560EMFS) and op-amps (MC33272A), as well as the soft-saturation inductor (XAL6060-223) and capacitor (PEG127KA3110Q) of the power stage . The parameter values of these devices were entered directly from the datasheet for the corresponding part, including the "Maximum Ratings" information.

While the simulation time for this switching circuit is significantly longer than for the abstract model, more detailed information about the circuit’s signals and components is available. This includes the component stress levels, which are monitored within all the "datasheet" models.

The companion design, "TDFS Loop Stability for Step-Down (Buck) DC to DC Converter - Switching", demonstrates a method to directly assess the open-loop frequency response, and hence the stability margin, of this converter. The TDFS (Time Domain Frequency Sweep) method circumvents the need for state-average models of the switching elements.