boost | PartQuest™ Explore

Copy of AC-DC Power Adapter With Current Boost Regulator - on Tue, 11/07/2023 - 17:15

Designer247180

Member for

1 year 8 months

6

designs

2

groups

Welcome to the community!!

Description

About text formats

Copy of NCV8876 - Automotive Start-Stop Boost Controller - on Thu, 10/12/2023 - 14:37

Designer250003

Member for

1 year 5 months

6

designs

1

groups

Welcome to the community!!

Description

This example shows the performance of an ON Semiconductor NCV8876 Automotive Grade Start-Stop Boost Controller:

http://www.onsemi.com/pub_link/Collateral/NCV8876-D.PDF

For vehicles with Start-Stop capability, the engine (ICE) is turned off during idle periods, for the purpose of fuel economy. But low-voltage nuisance drop-out of key electronic functions must be avoided during engine re-start. The NCV8876 is designed specifically for this purpose. It uses current-mode control, with many integrated functions to reduce the complexity of the external boost circuit.

Simulation results show the output to the load during battery drop-out and recovery. Note that in this application, the output voltage (dark blue waveform) is maintained above 6.4V during the drop-out transient, and regulates at 6.8V during sustained low voltage (4V) battery operation (orange waveform).

This circuit also demonstrates the value of soft-saturation inductor components from Coilcraft:

http://www.coilcraft.com/pdfs/Doc1140_Beyond_the_data_sheet_Part1.pdf

The load current for the XAL4030-332 inductor in this application is 4A during nominal 12V operation. But during boost operation, the current reaches 6.6A peak (light blue waveform). This could saturate a typical inductor if it were sized for the nominal load, resulting in a collapse of the effective inductance. But notice that the actual instantaneous inductance (green waveform) only drops to 2.2uH, for this nominal 3.3uH part. This relatively small percentage drop in inductance can easily be accommodated by the converter design.

About text formats

Copy of AC-DC Power Adapter With Current Boost Regulator - on Tue, 08/22/2023 - 21:14

Designer132741

Member for

7 years 9 months

17

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Copy of AC-DC Power Adapter With Current Boost Regulator - on Fri, 02/26/2021 - 18:56

Designer238407

Member for

4 years 1 month

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Copy of AC-DC Power Adapter With Current Boost Regulator - on Fri, 02/26/2021 - 18:56

Designer238407

Member for

4 years 1 month

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Copy of boost converter average model open loop - on Wed, 02/24/2021 - 20:39

Designer19

Member for

11 years 4 months

1,771

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

boost converter average model open loop

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

Boost converter average model

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrodynamic energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.

The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.

The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.

In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).

In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.

In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

Copy of NCV8876 - Automotive Start-Stop Boost Controller - on Sun, 11/29/2020 - 21:55

Designer237324

Member for

4 years 3 months

0

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the performance of an ON Semiconductor NCV8876 Automotive Grade Start-Stop Boost Controller:

http://www.onsemi.com/pub_link/Collateral/NCV8876-D.PDF

For vehicles with Start-Stop capability, the engine (ICE) is turned off during idle periods, for the purpose of fuel economy. But low-voltage nuisance drop-out of key electronic functions must be avoided during engine re-start. The NCV8876 is designed specifically for this purpose. It uses current-mode control, with many integrated functions to reduce the complexity of the external boost circuit.

Simulation results show the output to the load during battery drop-out and recovery. Note that in this application, the output voltage (dark blue waveform) is maintained above 6.4V during the drop-out transient, and regulates at 6.8V during sustained low voltage (4V) battery operation (orange waveform).

This circuit also demonstrates the value of soft-saturation inductor components from Coilcraft:

http://www.coilcraft.com/pdfs/Doc1140_Beyond_the_data_sheet_Part1.pdf

The load current for the XAL4030-332 inductor in this application is 4A during nominal 12V operation. But during boost operation, the current reaches 6.6A peak (light blue waveform). This could saturate a typical inductor if it were sized for the nominal load, resulting in a collapse of the effective inductance. But notice that the actual instantaneous inductance (green waveform) only drops to 2.2uH, for this nominal 3.3uH part. This relatively small percentage drop in inductance can easily be accommodated by the converter design.

About text formats

Copy of NCV8876 - Automotive Start-Stop Boost Controller - on Sun, 11/29/2020 - 21:55

Designer237324

Member for

4 years 3 months

0

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example shows the performance of an ON Semiconductor NCV8876 Automotive Grade Start-Stop Boost Controller:

http://www.onsemi.com/pub_link/Collateral/NCV8876-D.PDF

For vehicles with Start-Stop capability, the engine (ICE) is turned off during idle periods, for the purpose of fuel economy. But low-voltage nuisance drop-out of key electronic functions must be avoided during engine re-start. The NCV8876 is designed specifically for this purpose. It uses current-mode control, with many integrated functions to reduce the complexity of the external boost circuit.

Simulation results show the output to the load during battery drop-out and recovery. Note that in this application, the output voltage (dark blue waveform) is maintained above 6.4V during the drop-out transient, and regulates at 6.8V during sustained low voltage (4V) battery operation (orange waveform).

This circuit also demonstrates the value of soft-saturation inductor components from Coilcraft:

http://www.coilcraft.com/pdfs/Doc1140_Beyond_the_data_sheet_Part1.pdf

The load current for the XAL4030-332 inductor in this application is 4A during nominal 12V operation. But during boost operation, the current reaches 6.6A peak (light blue waveform). This could saturate a typical inductor if it were sized for the nominal load, resulting in a collapse of the effective inductance. But notice that the actual instantaneous inductance (green waveform) only drops to 2.2uH, for this nominal 3.3uH part. This relatively small percentage drop in inductance can easily be accommodated by the converter design.

About text formats

Terms of Use Cookie Notice Data Privacy Notice