Amplifier | PartQuest™ Explore

Application Area

Designer155951

Member for

7 years 8 months

18

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

flitro paso bajo

Designer151861

Member for

7 years 9 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

About text formats

Loudspeaker with Simple Amplifier

Designer101516

Member for

8 years 5 months

4

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.&#13;Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!&#13;*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

amp_op_inversor

Designer129086

Member for

8 years 1 month

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Class A Amplifier

Designer121961

Member for

8 years 2 months

52

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

current amplifier

Designer114336

Member for

8 years 4 months

10

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

BJT Common Emitter Amplifier

Designer80311

Member for

8 years 8 months

7

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

BJT Common Emitter Amplifier

Designer79991

Member for

8 years 8 months

27

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

BJT VHF Mixer 130Mhz

Designer105111

Member for

8 years 5 months

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Loudspeaker with Simple Amplifier

Designer12806

Member for

9 years 7 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.&#13;Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!&#13;*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Troubleshooting Terms of Use Cookie Notice Data Privacy Notice