555 Timer | PartQuest™ Explore

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Mon, 09/25/2023 - 13:23

Designer247440

Member for

2 years 4 months

7

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

555 Timer, With Decoupling Capacitors, Driving Ladders of LED's |

Designer114371

Member for

8 years 8 months

20

designs

groups

555 Timer, With Decoupling Capacitors, Driving Ladders of LED's |

Designer114371

Member for

8 years 8 months

20

designs

groups

Copy of Timer 555 with D flip flop | 03 Sep 2022 - on Fri, 09/08/2023 - 10:42

Designer249249

Member for

2 years 2 months

designs

groups

Welcome to the community!!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 07/05/2023 - 10:40

Designer247277

Member for

2 years 4 months

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 07/05/2023 - 10:40

Designer247277

Member for

2 years 4 months

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 07/05/2023 - 10:40

Designer247277

Member for

2 years 4 months

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 07/05/2023 - 10:40

Designer247277

Member for

2 years 4 months

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 07/05/2023 - 10:40

Designer247277

Member for

2 years 4 months

designs

groups

Welcome to the community!!

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the&nbsp;diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!